How to Fix Common Bobcat Toolcat Problems?

The Bobcat Toolcat comes with a fleet of equipment that makes it easier for people to do more than enough regarding landscaping, carbo lifting, towing, and more. However, the intelligent utility vehicle is not out of any problems. But, the issues are fixable. So, don’t worry.

Among a long list of issues, some of the most common bobcat toolcat problems are contaminated hydraulic fluid filter, blown steering hoses, defective glow plugs, bad steering sensor, etc.

Well, don’t panic if you’ve encountered one of those problems above. We are going to share the most straightforward troubleshooting steps for the abovementioned problems. So, never miss reading this article to the end.

What Are The Common Bobcat Toolcat Problems?

Unfortunately, the problem with the Bobcat Toolcat is more or less frequent in almost all the models. Whether it is 5600, UW54, or UW56, any problems can occur anytime and for any reason.

Some of the most common problems of the Bobcat Toolcat are mentioned below.

• Contaminated hydraulic fuel filter.
• Blown steering hose.
• Defective glow plugs.
• Wheel steering sensor.
• Damaged battery

5 Solutions For Bobcat Toolcat Problems

You know the most common problems of Bobcat Toolcat. Now, it’s time to fix the problems one by one. Moreover, experts recommend taking any troubleshooting steps only when you are pretty much sure about what causes the problems.

Let’s find out the possible solutions to the problem using your utility vehicle Bobcat Toolcat without hesitation.

1. Replace Contaminated Hydraulic Fuel Filter

If the bobcat toolcat utility work machine’s fuel filter becomes clogged or contaminated due to additional dirt or debris, it also causes the contaminants to enter the engine.

Therefore, if the contaminants enter the engine, they are more likely to cause wear and tear on the engine. Due to this, the performance of Bobcat Toolcat drops dramatically. Therefore, it should be changed.

Furthermore, experts suggest changing the hydraulic fuel filter after the first 50 hours of using your Bobcat Toolcat.

Let’s look at the quick steps below to replace the contaminated hydraulic filter on your Bobcat Toolcat.

• Step 1: Park your Bobcat Toolcat on the flat or leveled surface.
• Step 2: Stop the engine and raise the rear cover of your Bobcat Toolcat.
• Step 3: Lift the cooling package into the service position.
• Step 4: Remove the coolant hose if your Bobcat Toolcat has any. You will find the hose in the upper right-hand corner of the cooling package.
• Step 5: Remove all the mounting bolts that support the cooling package.
• Step 6: Secure the cooling package in the service position.
• Step 7: Locate the hydraulic fuel filter on the left side of the rear wheel.
• Step 8: Put a pan under the hydraulic fuel filter to grab any excessive fuel dropping on the ground.
• Step 9: Take a wrench, plate it on the fuel filter’s lower part and loosen it.
• Step 10: Loosen the filter with your hands and pull it out.
• Step 11: Clean the filter housing.
• Step 12: Install a new filter on your Bobcat Toolcat.

In order to replace the hydraulic air filter on your Bobcat Toolcat, you need to pay around $15-$30, depending on the model.

Furthermore, you need to add another $70-$80 to pay as a labor cost if you cannot replace the fuel filter.

2. Blown Steering Hose

This is another most frequent problem of Bobcat Toolcat, which often causes significant issues when it comes to operating it. Moreover, the hose often becomes corroded, blown, or damaged; without a second thought, you need to replace it.

One of the easiest ways to solve the blown steering hoses is to use an attachable hose fitting and connect the two steering hoses.

Here, the bottom of the fitting collars will spin into hoses, and the top will screw down into the bottom of another fitting collar.

• Step 1: Cut the steering hoses using a hose cutter. You can also use a hacksaw blade in this case.
• Step 2: Place the attachable hose fitting into the steering hoses.
• Step 3: Connect the top collar of one hose to the bottom collar of another. Use a wrench to tighten the attachable hose fittings on your Bobcat Toolcat.

So, you are done with fixing the issue of blown or defective steering hoses.

Note: The method we showed above is temporary action to fix the blown steering hose issue. That’s why you always try to keep some attachable hose fittings with your Bobcat Toolcat.

You will find different types of attachable hose fittings made of other materials on the market. In this case, you should have one JIC male and one JIC female hose fighting, which will cost you around $40-$60.

3. Clean or Replace the Defective Glow Plugs

The glow plugs in your Bobcat Toolcat play a massive role in ensuring proper fuel consumption. Without adequate functioning of the glow plugs, the engine can’t run your Bobcat Toolcat smoothie.

So, as we are discussing issues related to Bobcat Toolcat, the fact of defective glow plugs comes into play.

But what should you do to eliminate the defective glow plugs issue? Well, the foremost thing you should do is clean or replace the glow plugs. You will find a total of 4 glow plugs on your Bobcat Toolcat.

Therefore, when fixing the issue of defective glow plugs, ensure you inspect all the glow plugs one after another. White smoke, black smoke, decreased fuel efficiency and poor engine performance are the symptoms of defective or corroded glow plugs.

• Step 1: Locate the glow plugs on the top of the cylinder head on your Bobcat Toolcat.
• Step 2: Carefully remove the wires of the glow plugs.
• Step 3: Pull out the glow plugs from their sockets.
• Step 4: Clean the glow plugs properly.
• Step 5: Reinstall the glow plugs properly with the wires.

Note: If cleaning the corroded glow plugs doesn’t work, you should replace them as soon as possible. Furthermore, make sure the electrical wires of the glow plugs are good.

In order to replace the glow plugs on your Bobcat Toolcat, you need to spend around $30-$40 to buy a set of glow plugs. Moreover, changing the glow plugs on utility vehicles is not rocket science. In most cases, you can do the job on your own.

But then again, it will cost you $150-$200 to go with the mechanic in this regard.

4. Replace the bad steering position sensor

The steering position sensor located on the steering column of your Bobcat Toolcat plays a massive role in monitoring wheel position and rate of turn. If the steering position sensor in your Bobcat Toolcat goes bad, you can’t drive the vehicle.

If the wheel position sensor goes or becomes defective, you can notice symptoms like a traction control light coming on, loss of control over driving, the engine slowing down, etc.

In this case, you should replace the bad or defective steering position sensors on your Bobcat Toolcat.

• Step 1: Locate the steering position sensor on the steering cylinder by the hose clamps.
• Step 2: Unscrew the two hose clamps using a screwdriver.
• Step 3: Pull out the steering position sensor using your hands.
• Step 4: Install a new steering position sensor. Make sure you tighten the two hose clamps properly.

Replacing the steering position sensor on your Bobcat Toolcat will cost you $50-$250 based on your type of Bobcat Toolcat.

You need to add another $470-$150 as a labor cost if you are not able to do the job on your own.

5. Replace the Damage Battery

This is another most frequent cause with the Bobcat Toolcat. However, if the battery of your Bobcat Toolcat becomes damaged or defective, you need to repair or replace the battery based on its condition.

But, the express recommends replacing the battery so that you don’t need to repair it regularly.

• Step 1: Locate the battery on the engine bay of your Bobcat Toolcat.
• Step 2: Remove the battery clamp bracket.
• Step 3: Pull out the battery cable.
• Step 4: Remove the plastic holding on your Bobcat Toolcat battery using a wrench.
• Step 5: Pull out the battery using your hands.
• Step 6: Remove the positive battery terminal.
• Step 7: Install the new battery and reverse the steps above.

Replacing the battery of the Bobcat Toolcat is not rocket science. So, you can easily replace the battery if you have some tools.

You need to pay around $150-$400. Besides, it will cost $150-$200 more if you want to go with the mechanic.

Frequently Asked Questions (FAQs)

Now you will see some frequently asked questions by Bobcat Toolcat owners or people who tend to buy it. This section will help you if you are from one of the groups, maybe both.

Conclusion

Similar to any other utility vehicle, having issues with the Bobcat Toolcat is nothing unfamiliar. However, a lack of maintenance, rough driving, additional weight, and other variables cause the Bobcat Toolcat problem in most cases.

Therefore, it is always better to emphasize the maintenance of the Bobcat Toolcat. Besides, whenever you notice any malfunction, you should hurriedly inspect the issues and solve them as soon as possible.

The troubleshooting steps mentioned above will work as a guideline for you regarding Bobcat Toolcat’s everyday issues. Last but not least, never feel shy going with professionals if you think you can’t fix the problems independently.